Tuesday, February 09, 2010

VOIP: Set Up Asterisk and LinkSys 3102 to work with SIPDroid.

My most recent project has been to set up a VOIP setup on my Droid so that I can VPN into my home network using either my 3G service or WiFi and use the unused landline that I have so that I don’t burn minutes. As a secondary objective, I’d also like to be able to have calls made to my house ring on my cell phone after a few rings on my house phone.

In order to accomplish this task, I needed 2 things:

A means to connect my landline to my Asterisk server

An old machine to run Asterisk on

The old machine was easy. I have an old Compaq that has been sitting idle since the early 2006 or 2007. It had Ubuntu Dapper Drake. Although I would have liked to have put something newer, it appears that most newer distributions don’t agree with the hardware, and I really don’t have time to mess around with passing in various kernel parameters in a trial and error manner since the error messages were non-existent. Since this was the case, I enabled the universe repository under /etc/apt/sources.list, and ran the following command to get Asterisk running:

apt-get –f install asterisk

I didn’t change any of the configuration files, I want to keep them stock since I will use a special configuration wizard.

Now, the hardware I used to connect the phone was a Linksys 3102 ATA. I also did not do anything in configuration outside of enabling configuration through the outside WAN since this is only connected to my Intranet.

Configuration, despite how confusing all this looked initially, turned out to be a piece of cake, thanks to this handy dandy configuration utility, courtesy of the nice folks at Voxilla. I simply followed the wizard, which automatically configured the 3102 to work with Asterisk. To configure Asterisk, I made a backup of the sip.conf, voicemail.conf, and extensions.conf, removed them, and copy and pasted in the appropriate configuration sections from the wizard into the appropriate files. So, to do that, it looked something like:

root@cloya-desktop:/etc/asterisk# mkdir backup

root@cloya-desktop:/etc/asterisk# cp sip.conf backup/

root@cloya-desktop:/etc/asterisk# cp extensions.conf backup/

root@cloya-desktop:/etc/asterisk# cp voicemail.conf backup/

root@cloya-desktop:/etc/asterisk# rm sip.conf

root@cloya-desktop:/etc/asterisk# nano sip.conf

root@cloya-desktop:/etc/asterisk# rm voicemail.conf

root@cloya-desktop:/etc/asterisk# nano voicemail.conf

root@cloya-desktop:/etc/asterisk# rm extensions.conf

root@cloya-desktop:/etc/asterisk# nano extensions.conf

root@cloya-desktop:/etc/asterisk# cat sip.conf

[digiassn]

type=friend

host=dynamic

context=home

secret=secretPassword

mailbox=digiassn

dtmfmode=rfc2833

disallow=all

allow=ulaw

[pstn]

; If you're using Asterisk, this goes into the Incoming settings

; For your Trunk

type=friend

host=dynamic

; If using Asterisk@home, change the below line to context=from-internal

context=home

secret= secretPassword

dtmfmode=rfc2833

disallow=all

allow=ulaw

insecure=very

[pstn-spa3k]

; If you're using Asterisk, this section goes into the Outgoing Settings

; for your trunk.

type=peer

auth=md5

host=192.168.1.110

port=5061

secret= secretPassword

username=asterisk

fromuser=asterisk

dtmfmode=rfc2833

; If using Asterisk@home, change the below line to context=from-internal

context=home

insecure=very

root@cloya-desktop:/etc/asterisk# cat voicemail.conf

[default]

digiassn => digiassn,John Ward,user.com,user-pager.com,tz=pacific

root@cloya-desktop:/etc/asterisk# cat extensions.conf

[home]

exten => digiassn,1,Ringing

exten => digiassn,2,Dial(SIP/digiassn,20,T)

exten => digiassn,3,Voicemail(udigiassn)

exten => digiassn,4,Hangup

exten => 911,1,Dial(SIP/911@pstn-spa3k,60,)

exten => 911,2,Congestion

exten => _XXXXXXX,1,Dial(SIP/${EXTEN}@pstn-spa3k,60,)

exten => _XXXXXXX,2,Congestion

exten => _1800XXXXXXX,1,Dial(SIP/${EXTEN}@pstn-spa3k,60,)

exten => _1800XXXXXXX,2,Congestion

exten => _1888XXXXXXX,1,Dial(SIP/${EXTEN}@pstn-spa3k,60,)

exten => _1888XXXXXXX,2,Congestion

exten => _1877XXXXXXX,1,Dial(SIP/${EXTEN}@pstn-spa3k,60,)

exten => _1877XXXXXXX,2,Congestion

exten => _1866XXXXXXX,1,Dial(SIP/${EXTEN}@pstn-spa3k,60,)

exten => _1866XXXXXXX,2,Congestion

Then, I need to edit the /etc/default/asterisk file to change the line that says

RUNASTERISK=no

to say

RUNASTERISK=yes

Now, before I actually start this up, I needed to make one final change. When I actually started this up and played with it, the dial in from my land line did not ring the VOIP setup on my Droid the way I wanted. The reason is the extension.conf file was not set up correctly from the script. The way it works by default is that any calls coming in the digiassn extension would ring the digiassn extension for 20 seconds then go to voice mail. This is not what I want. I want calls coming in the pstn extension to ring the pstn extension for 20 seconds (which would be the physical home phone line), then ring my VOIP setup on my cell (digiassn) for 10 seconds, then go to voicemail. Most normal configurations won’t require this, but I included it here to show my final configuration. First, go into the SPA configuration utility, and under Voice/Line 1/Proxy and Registration, change the value of Use Outbound Proxy to true. I don’t know why, but the handset wouldn’t ring without this set. Then change the below configuration for extensions.conf:

[home]

exten => pstn,1,Ringing

exten => pstn,2,Dial(SIP/digiassn,20,T) #ring the handset first

exten => pstn,3,Dial(SIP/pstn,15,T) #then ring the SIPDroid

exten => pstn,4,Voicemail(udigiassn)

exten => pstn,5,Hangup

exten => 911,1,Dial(SIP/911@pstn-spa3k,60,)

exten => 911,2,Congestion

exten => _XXXXXXX,1,Dial(SIP/${EXTEN}@pstn-spa3k,60,)

exten => _XXXXXXX,2,Congestion

exten => _1800XXXXXXX,1,Dial(SIP/${EXTEN}@pstn-spa3k,60,)

exten => _1800XXXXXXX,2,Congestion

exten => _1888XXXXXXX,1,Dial(SIP/${EXTEN}@pstn-spa3k,60,)

exten => _1888XXXXXXX,2,Congestion

exten => _1877XXXXXXX,1,Dial(SIP/${EXTEN}@pstn-spa3k,60,)

exten => _1877XXXXXXX,2,Congestion

exten => _1866XXXXXXX,1,Dial(SIP/${EXTEN}@pstn-spa3k,60,)

exten => _1866XXXXXXX,2,Congestion

Now, I can start up Asterisk by running /etc/init.d/asterisk restart.

Now, I need a VOIP client. I am using SIPDroid to make my connections. To do this, I configure SIPDroid as follows:

Under SIP Account Settings:

Authorization Username: pstn

Password:

Server: 192.168.1.111 (The address of the Asterix box).

Port: 5060

Protocol: UDP

Everything else I leave default. That’s it. When I’m connected to my WiFi network, I can use the VoIP setup to connect directly to my landline.

So, after using this for a day, there were some definite things I wanted to change. The dial plan that is on by default sucked. Since I am using Android and SIPVoice to dial, and by default SIPDroid uses the full number mask stored in contacts (XXX-XXX-XXXX), Asterisk refused to dial. I would see SIPDroid try to dial but hang up immediately without completing the call. Took me a while to figure out what was going on, so some new dial masks needed to be created. Voicemail was not set up correctly. Since I don’t have an answering machine on my landline, I figured Asterisk can play double duty and serve as an answering machine as well. The wizard doesn’t create a workable voicemail password, so that needed to be fixed. Also, after some investigation, it turns out that Asterisk also has a little feature that works just like the Telezapper, and will play the “out of service” tone when you answer a phone so telemarketers and such will register you in the Do Not Call database. This is a feature that I need to have since the National Do Not Call database is such a joke. There are also all sorts of neat scripts you can run to forward telemarketers to annoying endless voice prompt loops, or just hang up on them, but I won’t cover them here.

So, to accomplish what I wanted, I modified all three configuration files like so.

Voicemail.conf:

[default]

digiassn => 1234,John Ward,john@email,tz=pacific

Note the 1234. This is the 4 digit numeric password you need to enter to check and manage your voicemailbox.

Extensions.conf:

[home]

exten => pstn,1,Ringing

#add zapateller

exten => pstn,2,Zapateller(answer)

exten => pstn,3,Dial(SIP/digiassn,15,T)

exten => pstn,4,Dial(SIP/pstn,10,T)

exten => pstn,5,Voicemail(udigiassn)

exten => pstn,6,Hangup

exten => 911,1,Dial(SIP/911@pstn-spa3k,60,)

exten => 911,2,Congestion

#dialing 9999 will get me my voicemail box

exten => 9999,1,VoiceMailMain(digiassn)

#dialmasks, local calls

exten => _XXXXXXX,1,Dial(SIP/${EXTEN}@pstn-spa3k,60,)

exten => _XXXXXXX,2,Congestion

#if coming from cell phone, only take the phone number, minus the 1 and the area code

exten => _1210XXXXXXX,1,Dial(SIP/${EXTEN:-7}@pstn-spa3k,60,)

exten => _1210XXXXXXX,2,Congestion

#same as above, only without the 1. this is for local calls

exten => _210XXXXXXX,1,Dial(SIP/${EXTEN:-7}@pstn-spa3k,60,)

exten => _210XXXXXXX,2,Congestion

#Any other number, with the 1

exten => _1XXXXXXXXXX,1,Dial(SIP/${EXTEN}@pstn-spa3k,60,)

exten => _1XXXXXXXXXX,2,Congestion

#without the 1

exten => _XXXXXXXXXX,1,Dial(SIP/1${EXTEN}@pstn-spa3k,60,)

exten => _XXXXXXXXXX,2,Congestion

#dont believe the rest need to be here, but I will leave them jic

exten => _1800XXXXXXX,1,Dial(SIP/${EXTEN}@pstn-spa3k,60,)

exten => _1800XXXXXXX,2,Congestion

exten => _1888XXXXXXX,1,Dial(SIP/${EXTEN}@pstn-spa3k,60,)

exten => _1888XXXXXXX,2,Congestion

exten => _1877XXXXXXX,1,Dial(SIP/${EXTEN}@pstn-spa3k,60,)

exten => _1877XXXXXXX,2,Congestion

exten => _1866XXXXXXX,1,Dial(SIP/${EXTEN}@pstn-spa3k,60,)

exten => _1866XXXXXXX,2,Congestion

2 comments:

cheap dublin hotels said...

This post seems so geeky but still this is one of my jobs.. To learn about technology, setting it up and all.. i a geek because i am a programmer.

Aileen said...

Thanks for this tech support.